Techno-Frontier 2020 in Makuhari Messe, April 8-10, 2020
We will join Techno-Frontier 2020 in April. Date: 2019.4.8 WED ~ 4.10 FRIITG Booth No: 5G-38The exhibition was held in Makuhari Messehttps://www.jma.or.jp/tf/en/index.html
APEC 2020, New Orleans Ernest N. Morial March 15-19
Visit ITG at APEC 2020, New Orleans Ernest N. Morial March 15 - 19Booth #854Rickey Cheang, Field Application Engineer of ITG Electronics, Inc. will present “Selecting The Right Inductor for Buck Converter Application” at APEC 2020 on Tuesday, March 17, 3:15-3:45 PM Exhibit Theater 4www.apec-conf.org/ https://www.facebook.com/APEC-Applied-Power-Electronics-Conference-114419428583664/ Exposition HoursMonday, March 16 5:00 PM – 8:00 PMTuesday, March 17 12:00 PM – 5:00 PMWednesday, March 18 10:00 AM – 2:00 PMITG’s engineering staff will be at the show to answer your questions about Power Inductors, Molded Inductors, Common Mode Chokes, Flat Wire Common Mode Chokes, Flat Wire Inductors, and our complete selection of Magnetics products.Need something now….go to… ITG-Electronics.com
The Battery and Electric & Hybrid Show in Novi MI between September 10 to 12, 2019
We will join the Battery and Electric & Hybrid Show in Novi MI between September 10 to 12, 2019Booth #806The Battery Show is North America's largest and most comprehensive advanced battery manufacturing trade show. Combined with the Electric & Hybrid Vehicle Technology Expo, more than 650 suppliers come together to showcase their raw materials, components, cell makers, testing, and recycling products and services. https://thebatteryshow.com/
APEC 2019 in Anaheim, California, March 17-21, 2019
Visit ITG at APEC, Anaheim, CA March 18-19-20,Booth #866Rickey Cheang, Field Application Engineer of ITG Electronics, Inc. will present “Electrical Noise Suppression and Common Mode Choke” at APEC 2019 on Wednesday, March 20, 2019-11:15AM-11:45AM Room 212AB www.apec-conf.org/For more information, please check the following presentations:Using Flat Wire Common Mode Chokes Comes With Advantages….The primary advantage is a greater surface area. Flat wire maximizes usable wire at high frequencies due to increased surface area.https://www.eedesignit.com/using-flat-wire-common-mode-chokes-advantages-itg/New Nanocrystalline Common Mode Chokes…. high permeability allows for fewer turns to achieve the same inductance. This enables nanocrystal cores to boast a much lower DCR (Direct Current Resistance) and reduce component size than Ferrite core materials.https://www.eedesignit.com/check-it-out-at-apec-2019-new-nanocrystalline-common-mode-chokes/_____________________________________________________________________________________________ITG’s engineering staff will be at the show to answer your questions about Power Inductors, Molded Inductors, Common Mode Chokes, Flat Wire Common Mode Chokes, Flat Wire Inductors, and our complete selection of Magnetics products.Need something now….go to… ITG-Electronics.com
Techno-Frontier 2019 in Makuhari Messe, April 17-19, 2019
We will join Techno-Frontier 2019 in April. Date: 2019.4.17 WED ~ 4.19 FRIITG Booth No: 6A-07The exhibition was held in Makuhari Messewww.jma.or.jp/tf/en/index.html
Registration, Evaluation, Authorization and Restriction of Chemicals (REACH) Certificate of Complian
REACH 191 per the EChA 06/27/2018This is to certify that the above mentioned part(s) are REACH Compliant with the EU directive. NO ITG magnetics products contain Substances of Very High Concern (SVHC) as listed by the European Chemicals Agency (EChA) under the provisions of Regulation (EC) No. 1907/2006 of the European Parliament and of the council concerning the REACH 191 per the EChA 06/27/2018 and previous updates.For a full list of chemicals included in EChA 191 visit the REACH website HereIf you require any further information, feel free to contact us.
RoHS and Halogen Free and REACH Declaration of Compliance
ITG Electronics,INC (ITG) also declares that all its magnetics products are compliant to the Registration, Evaluation, Authorisation, Restriction of Chemicals (REACH) and Halogen Free limit.Based on information obtained from our component suppliers, ALL ITG magnetics products are fully RoHS 2 compliant
New Line of Flat Wire Common Mode Chokes
ITG ELECTRONICS INC. ITG Electronics introduces New Line of Flat Wire Common Mode Chokes. Elmsford, NY February 2018 – ITG Electronics, a leading manufacturer of Inductors and Transformers in business since 1963, now offers a range common footprints as well as custom flat wire common mode chokes (CMC) for high power density and high frequency switching.Flat wire CMCs utilize a flattened, rectangular cross section, copper wire instead of a traditional, circular cross section, wire. The primary advantage is a greater surface area. At high frequencies, the current penetrates and utilizes less and less of the volume of the copper wire. This is called the skin effect, because at high frequencies only the ‘skin’ of the wire is utilized. Flat wire maximizes usable wire at high frequencies due to increased surface area. This advantage has rippling effects through other aspects of the CMC performance as well. In general, the higher the frequency, the lower the permissible current through a specific wire, again, due to the skin effect, because the current is not utilizing all of the available wire. This means part of the wire is wasted, driving up resistance and heat in addition to lowering the current rating. With a flat wire CMC all these effects are stifled as the current is able to use the whole wire more efficiently. The altered geometry of the wire also allows for a much lower distributed capacitance at high frequencies. This enables the choke to have higher impedance over a higher range of frequencies and therefore better performance as a choke.Flat wire CMC’s not only use current more efficiently, they use space more efficiently. A flat wire can easily exceed window fill and winding density of its round wire counterparts. Changing core geometry from a traditional toroid to the rectangular core pictured above can yield savings of up to 50% in volume for the exact same performance. Putting it all together, the result is a high energy density part that takes up less space, uses less power, and can operate at a higher frequency. For more information, visit www.ITG-Electronics.com , ITG Electronics, 175 Clearbrook Elmsford, NY 10523 Email: sales@ITG-Electronics.comABOUT ITG ELECTRONICS INC: ITG Electronics headquarters is Elmsford, New York. ITG specializes in wire-wound power magnetic components design, product development and manufacturing. ITG is a preferred supplier for magnetics components to many US and worldwide major electronics OEM’s. ITG factories are TS16949, ISO9000, ISO14000, OHSAS18000, QC0800000, ISO14064 Certified.
Your Checklist to Selecting an EMI Filter Design
We have published an EMI (ElectroMagnetic Interference) Filter Design checklist for you.Run through this quick checklist of EMI filter design requirements so you don’t overlook any necessary information, such as current regulations, insertion loss, mounting methods, frequencies, terminations, etc.Download Your Checklist to Selecting an EMI Filter Design FREE now!
ITG releases NEW data and signal line filters for MRI Rooms
ITG Electronics, Inc (ITG), a global leader since 1963 in design and manufacturing of high quality electronic passive components is now producing data line filters specifically designed for MRI room applications. These filters will passively protect the datalines integrity and prevent interference from the other equipment in the room with a 100dB stop band all while maintaining a low leakage current. Click here to see our F2779Y series with 22AWG connection or here to see our F2780Y series with RJ45 connectors
APEC 2018 in San Antonio, Texas, March 4-8, 2018
We will exhibit APEC 2018 in San Antonio, Texas, March 4-8, 2018Our trade show booth# 308.Join us in attending this one of a kind conference!Rafik Stepanian, our VP of Engineering EMI Filters, has the distinct honor of presenting during the conference, come to support ITG and a great mind in the field of EMI!Session Title: COTS Filters for MIL-STD-461 ApplicationsSession Date and Time: Wednesday, March 7, 2018, 12:00pm-12:30pmSession Room: 217Ahttp://www.apec-conf.org
ITG announces support of Conflict Minerals Initiative
ITG Electronics Conflict Minerals Declaration
Techno Frontier 2017 in Tokyo from 2017/04/19-2017/04/21
ITG will again exhibit at Techno Frontier 20172017/04/19-2017/04/21 Techno Frontier 2017 at Makuhari Messe International Convention Complex in TokyoITG Booth No: 6P-16
9th Int'l Automotive Electronics Technology Expo 2017/01/18-2017/01/20
2017/01/18-2017/01/20 9th Int'l Automotive Electronics Technology Expo at Tokyo Big Sight in Tokyo
From March 20th 2016 - March 24th 2016 at Long Beach Convention Center in Long Beach CA.