US TSCA PBT Substances Declaration
ITG Electronics, Inc (ITG) declares that all its magnetics products are not contain any of the below listed Presistent, Bioaccumulative, and Toxic (PBT) substances as restricted under US Code of Federal Regulation title 40, part 751-"Regulation of Certain Chemical Substances and Mixtures under section 6 of The Toxic Substances COntrol Act" (TSCA).
RoHS and Halogen Free Declaration of Compliance
ITG Electronics,INC (ITG) also declares that all its magnetics products are compliant to the Registration, Evaluation, Authorisation, Restriction of Chemicals (REACH) and Halogen Free limit. Based on information obtained from our component suppliers, ALL ITG magnetics products are fully RoHS 2 compliant
Registration, Evaluation, Authorization and Restriction of Chemicals (REACH) CoC
REACH 233 per the EChA 01/17/2023This is to certify that the above mentioned part(s) are REACH Compliant with the EU directive. NO ITG magnetics products contain Substances of Very High Concern (SVHC) as listed by the European Chemicals Agency (EChA) under the provisions of Regulation (EC) No. 1907/2006 of the European Parliament and of the council concerning the REACH 233 per the EChA 01/17/2023 and previous updates.For a full list of chemicals included in EChA 233 visit the REACH website Here if you require any further information, feel free to contact us.
The Battery and Electric & Hybrid Show in Novi MI between September 13 to 15, 2022
ITG will exhibit at Battery and Electric & Hybrid Show in Novi MI between September 13 to 15, 2022. Come visit us at Booth Number 2244 to see our latest product offering.The Battery Show is North America's largest and most comprehensive advanced battery manufacturing trade show. Combined with the Electric & Hybrid Vehicle Technology Expo, more than 650 suppliers come together to showcase their raw materials, components, cell makers, testing, and recycling products and services. https://thebatteryshow.com/
APEC 2022 in Houston, TX
ITG will exhibit at APEC 2022 in Houston, TX between March 21-23, 2022 at the George R. Brown Convention Center. Come visit us at Booth Number 211 to see our latest product offering.The Applied Power Electronics Conference (APEC) focuses on the practical and applied aspects of the power electronics business. This is not just a designer’s conference; APEC has something of interest for anyone involved in power electronics:Equipment OEMs that use power supplies and dc-dc converters in their equipmentDesigners of power supplies, dc-dc converters, motor drives, uninterruptable power supplies, inverters and any other power electronic circuits, equipment and systemsManufacturers and suppliers of components and assemblies used in power electronicsManufacturing, quality and test engineers involved with power electronics equipmentMarketing, sales and anyone involved in the business of power electronicsCompliance engineers testing and qualifying power electronics equipment or equipment that uses power electronics
NEW release: ITG White Paper - Power Bead SMT Process Guide Series
View the White Paper PDF here
New Line of Flat Wire Common Mode Chokes
ITG ELECTRONICS INC. ITG Electronics introduces New Line of Flat Wire Common Mode Chokes. Elmsford, NY February 2018 – ITG Electronics, a leading manufacturer of Inductors and Transformers in business since 1963, now offers a range common footprints as well as custom flat wire common mode chokes (CMC) for high power density and high frequency switching.Flat wire CMCs utilize a flattened, rectangular cross section, copper wire instead of a traditional, circular cross section, wire. The primary advantage is a greater surface area. At high frequencies, the current penetrates and utilizes less and less of the volume of the copper wire. This is called the skin effect, because at high frequencies only the ‘skin’ of the wire is utilized. Flat wire maximizes usable wire at high frequencies due to increased surface area. This advantage has rippling effects through other aspects of the CMC performance as well. In general, the higher the frequency, the lower the permissible current through a specific wire, again, due to the skin effect, because the current is not utilizing all of the available wire. This means part of the wire is wasted, driving up resistance and heat in addition to lowering the current rating. With a flat wire CMC all these effects are stifled as the current is able to use the whole wire more efficiently. The altered geometry of the wire also allows for a much lower distributed capacitance at high frequencies. This enables the choke to have higher impedance over a higher range of frequencies and therefore better performance as a choke.Flat wire CMC’s not only use current more efficiently, they use space more efficiently. A flat wire can easily exceed window fill and winding density of its round wire counterparts. Changing core geometry from a traditional toroid to the rectangular core pictured above can yield savings of up to 50% in volume for the exact same performance. Putting it all together, the result is a high energy density part that takes up less space, uses less power, and can operate at a higher frequency. For more information, visit www.ITG-Electronics.com , ITG Electronics, 175 Clearbrook Elmsford, NY 10523 Email: sales@ITG-Electronics.comABOUT ITG ELECTRONICS INC: ITG Electronics headquarters is Elmsford, New York. ITG specializes in wire-wound power magnetic components design, product development and manufacturing. ITG is a preferred supplier for magnetics components to many US and worldwide major electronics OEM’s. ITG factories are TS16949, ISO9000, ISO14000, OHSAS18000, QC0800000, ISO14064 Certified.
Techno Frontier 2018 from 2018/04/18-2018/04/20
We will join Techno-Frontier 2018 in April. Date: 2018.4.18 ~ 4.20 Venue: Makuhari Messe https://www.jma.or.jp/tf/en/index.html Booth Number: 6C-06
Your Checklist to Selecting an EMI Filter Design
We have published an EMI (ElectroMagnetic Interference) Filter Design checklist for you.Run through this quick checklist of EMI filter design requirements so you don’t overlook any necessary information, such as current regulations, insertion loss, mounting methods, frequencies, terminations, etc.Download Your Checklist to Selecting an EMI Filter Design FREE now!
ITG releases NEW data and signal line filters for MRI Rooms
ITG Electronics, Inc (ITG), a global leader since 1963 in design and manufacturing of high quality electronic passive components is now producing data line filters specifically designed for MRI room applications. These filters will passively protect the datalines integrity and prevent interference from the other equipment in the room with a 100dB stop band all while maintaining a low leakage current. Click here to see our F2779Y series with 22AWG connection or here to see our F2780Y series with RJ45 connectors
Techno Frontier 2017 in Tokyo from 2017/04/19-2017/04/21
ITG will again exhibit at Techno Frontier 20172017/04/19-2017/04/21 Techno Frontier 2017 at Makuhari Messe International Convention Complex in TokyoITG Booth No: 6P-16
ITG announces support of Conflict Minerals Initiative
ITG Electronics Conflict Minerals Declaration
9th Int'l Automotive Electronics Technology Expo 2017/01/18-2017/01/20
2017/01/18-2017/01/20 9th Int'l Automotive Electronics Technology Expo at Tokyo Big Sight in Tokyo